Fluke 2052 Advanced Wire Tracer Kit
The Fluke 2052 is an advanced wire tracer that quickly and accurately troubleshoots energized and de-energized wire in residential, commercial, and industrial environments up to CAT IV 600V. The Fluke Advanced Circuit Tracer offers the highest protection available on any wire tracer. The Fluke 2052 wire tracer is designed to protect technicians from the most dangerous levels of transient overvoltage, including spikes up to 8,000 V that can occur in industrial and utility environments, industrial plants, factories, and hospitals where critical equipment cannot be taken offline. The Fluke Advanced Wire Tracer has two options: Fluke 2052 Advanced Wire Tracer and Fluke 2062 Advanced Pro Wire Tracer with Smart Sensor. Check out the comparison chart below to see which works best for your application.
Key Features
- Locate energized and de-energized wires quickly and accurately in walls, ceilings, and floors
- Find breaks or opens and shorts
- Identify breakers and fuses easily
- CAT IV / 600 V safety rated
- Includes the i400 AC Current Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors
Overview
The Fluke cable tracer can find breaks or opens and shorts whether troubleshooting electrical wiring and equipment in residential homes, commercial building, or high-voltage utility plants. The Fluke advanced wire tracer offers different modes and functions, giving the flexibility to troubleshoot a wide range of electrical wiring and circuitry problems you might encounter on the job.
Four Receiving Tracing Modes using the Fluke Advanced Wire Tracer
The 2052-R Receiver detects the signal in wires and cables using two methods: passive tracing without the transmitter for non-contact voltage detection and active tracing with the transmitter for all other modes. The receiver’s tip sensor can trace wires in corners, tight spaces, and junction boxes.
- “Quick Scan” mode for energized wire detection and visualization on the large color LCD
- “Precision” mode for more precise detection of a wire
- “Breaker” mode for easy breaker and fuse identification based on the highest recorded signal detected from the transmitter
- “Non-Contact Voltage Detection” mode to trace energized wires without the use of the transmitter
The Receiver can directly detect a signal on a wire through walls, floors, ceilings, and non-metallic conduits or pipes. However, to indirectly trace a wire in a non-metallic conduit or pipe, its necessary to use conductive fish tape or wire.
The Receiver cannot directly detect a signal on a wire through a metallic conduit or pipe, so using the junction box method to indirectly trace wires in metallic conduits would be used.
Three Transmitter Power Modes using the Fluke Advanced Circuit Tracer
The 2000-T Transmitter works on energized and de-energized circuits up to CAT IV 600 V and features high, low, and loop modes. These modes change the strength of the induced signal and can help provide more accurate results, depending on the circuit you’re tracing.
- “High” mode for normal energized and de-energized circuits
- “Low” mode for precision tracing with a low signal to reduce coupling to nearby wires and metal objects
- “Loop” mode for closed loop de-energized circuits
Two Transmitter Output Frequencies
The 2000-T automatically senses whether the system is energized or de-energized and generates a signal in the optimal 6 kHz or 33 kHz output frequency to trace a wire in either system with precision.
Eight Receiver Sensitivity Levels
More sensitivity levels mean more flexibility and accuracy when tracing
Fluke i400 Current Clamp
When a direct connection to a conductive wire is not possible, use the included i400 Current Clamp with the “Loop” mode on the Transmitter to induce a boosted 6 kHz signal through the insulation around the wire. The Clamp works on low-impedance closed circuits or to trace conduits or shielded wires grounded on both ends. However, a clamp signal is not as strong as a direct connection and may not be strong enough for the receiver to detect very far from the clamp.
What’s in the Box?
- Fluke 2052R Advanced Wire Tracer Receiver
- Fluke 2000T Advanced Wire Tracer Transmitter
- i400 AC Current Clamp
- Fluke 2000ACC Test Lead Accessory Kit for 2052/2062
- Premium hard carrying case
- Batteries
- Quick reference guide
- 1-year warranty
The Fluke Advanced Wire Tracers
Fluke 2052 Advanced Wire Tracer Kit w/ Clamp - CAT IV 600V, 2.5" LCD
Fluke 2062 Advanced Pro Wire Tracer Kit w/ Clamp - CAT IV 600V, 3.5" color LCD, Smart Sensor™
Wire Tracer Comparison
Proposition 65 Warning for California Residents: This product can expose you to chemicals including Benzene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to 
Related Items
(1)
Coming Soon
Free Shipping.
(12)
In Stock
Free Shipping.
(0)
Coming Soon
Free Shipping.
(0)
$2,899.99
Coming Soon
Free Shipping.