| Specifications: | Hobbes GIGATEST Compact Gigabit Ethernet Tester 256852
|
| Supported frame format | Ethernet II frame IEEE 802.3 frame
|
Interface
|
Left Side
| One 10/100/1000 Mbps UTP Ethernet port on–panel operation
|
| Right Side | -One USB port (mini–USB connector)
-One power switch
|
| Bottom Side | -One set of 16 scales rotary switch for different function modes
-Two sets of 16 scales rotary switch for ID control
-Two sets of 16 scales rotary switch in second for control of test duration
-One clear counter button
-One broadcast test packet button
-One Run/Stop test button
|
Speed and Link Mode
|
Auto Negotiation/Forced Mode
| -10/100Mbps Half/Full Duplex
-1000Mbps Full Duplex
|
| Traffic Generation |
Transfer rate
| -Wirespeed by test button on the device
-Customized in Mbps via configuration of utility software
-Asymmetric transfer rate by a pair of GIGATEST for ADSL test via
configuration of utility software
|
Packet length
| -Short packet length: 64 bytes by test button on the device
-Long packet length: 1518 bytes by test button on the device
-Random packet length: 64/128/256/512/768/1024/1518 bytes by
test button
-Specify fix length 64/128/256/512/768/1024/1518 bytes via
configuration of utility software
|
Payload in frame
| -Random by default button
-Selectable fix pattern, Byte increase, random or BERT via configuration
of utility software
|
Time based test
| -0~255 seconds by rotary switch on the device or 00 on two rotary switches
for infinite time till stop button is pressed
-Input test time required via configuration of utility software
|
| Packet based test | -Customized by packets counts via configuration of utility software
-Generate specified VLAN ID tagged packet
-Generate specified Destination IP/Source IP packet |
| Traffic Receiving |
| | • User–defined loss tolerance to identify Pass/Fail result of Loopback test
• No packet loss to identify Pass/Fail result of general test |
| Test Result |
| | • Pass or Fail LED indicator and log to show the result of test
|
Test Mode
|
| | • Bi–directional Symmetric Loop Test from utility software
• Bi–directional Asymmetric Loop Test from utility software
• Packet Generation Test from utility software
• User–defined test modes from A~E scales rotary switch.
• Test mode A~E can be changed randomly
• Provide pre–defined template A: P2P test, B: Packet Generation,
C: Web Access, D: Loopback Test, E: ADSL 10M/20M for fast configuration
• Default function and test modes from 0~9 scales rotary switch as below
|
| Function Mode by RotarySwitch (0~F) |
| 0, Servant mode | Switch to Servant mode and accepts control from Lord |
| 1, Short Packet | Symmetrical and bi–directional short packets (64 bytes length) test with test result. |
| 2, Long Packet | Same test as function 1 with long packets (1518 bytes length). |
| 3, Random Packet | Same test as function 1 with random (64~1518 byteslength) packets. |
| 4, BERT Loopback | Lord send BERT pattern to Servant for Loopback test by swapping DA and SA. |
| 5, Mesh Loop | Lord sends test packets to the 1st Servant, then the 1st
Servant forward packets to 2nd Servant. It is repeated until packets return to Lord. |
| 6, Web Access | Get IP from DHCP and download a specified file from Internet |
| 7, Broadcast packet | Send 60 broadcast frames per second in increased frame length |
| 8, Loopback (layer1) | Switch to layer 1 loopback mode (as servant) |
| 9, Loopback (layer2) | Same as function 8 with swapped DA and SA and recalculated CRC |
| A~E, Customized settings | Customized settings configured by PC such as ADSL network test |
| F, PC control | Control by PC via USB port. |
| LED Indicator |
| Power/Run | Power and Test Running status |
| Speed | Connection Speed, different blinking frequency shows different
speeds, able to identify 10Mbps, 100Mbps and 1000Mbps |
| Low Bat | Low battery warning |
| Get_IP | Status for getting IP from DHCP |
| TX | Data Transmission (fast blinking indicates Wirespeed) |
| RX | Data Receiving (fast blinking indicates Wirespeed) |
| Pass | Passed test result |
| Loopback | Loopback test in servant mode |
| Servant | Under Servant state |
| Connect | Connection status with other GIGATEST |
| CRC | Error CRC packet received |
| TX_loss | Packet loss at transmission side |
| RX_loss | Packet loss at receiving side |
| Fail | Failed test result |
| Hardware Counter |
| Tx Packet, Rx Packet, CRC Error Packet | Tx Bytes, Rx Bytes, Tx Rate, Rx Rate, Rx Broadcast Packet, Rx Multicast Packet,
Rx Unicast Packet, Rx Pause Packet, Rx VLAN Packet, Rx IPv4 Packet,Rx Dribble Packet,
Rx Alignment Error Packet, Rx Under Size Packet, Rx Over Size Packet, Rx 64
Bytes Packet, Rx 65–127 Bytes Packet, Rx 128–255 Bytes Packet, Rx 256–
511 Bytes Packet, Rx 512–1023 Bytes Packet, Rx 1024–1522 Bytes Packet |
| Software Support |
GIGATEST
| GIGATEST 1.0 is a GUI (graphic user interface) application
software for GIGATEST, which is for controlling, configuration, counters
data collecting and system upgrade of this machine.
|
Dimension
|
| | 141 x 22 x 22mm
|
| Temperature |
| Operating | 0°C to 40°C (32°F to 104°F) |
| Storage | 0°C to 50°C (32°F to 122°F) |
| Humidity |
| Operating | 0% to 85% RH |
| Storage | 0% to 85% RH |
| Power Source |
| | Two built–in 3.7V NI–MH batteries From USB cable via PC or external adapter
|
Proposition 65 Warning for California Residents: This product can expose you to chemicals including Benzene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to 
