Measure cable lengths up to 1000' (305 m) and provides connected switch information for troubleshooting active networks with this cable and network tester. Frequency-based measurements are used to validate network capacity up to 10 Gig and also provides distance to fault information with graphical wire map of cable under tests.
Measure cable lengths up to 1000' (305 m) and provides connected switch information for troubleshooting active networks with this cable and network tester. Frequency-based measurements are used to validate network capacity up to 10 Gig and also provides distance to fault information with graphical wire map of cable under tests.
Trusted for cable testing and provides all network testing needs, this cable and network tester is a handheld instrument designed for professionals to use in testing twisted pair cables, network connectivity, and PoE. In addition, this meter provides a solution for network connectivity problems and verifies cable performance up to 10 Gb/s. Performs nearest switch diagnostics to identify key network issues and validate switch configuration.
Features
| Cable Test | |
| Test Port | Shielded 8-pin modular jack accepts 8-pin modular (RJ45) plugs |
| Commissioning Autotests | 10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, Wire map Only Test Speed: 6 seconds for lengths <229.6' (70 m) |
| Cable Types | Balanced twisted-pair cabling Unshielded twisted-pair Screened twisted-pair 2-pair and/or 4-pair |
| Wire Map-Only Tests | Document wire map Length of each pair Diagnose split pairs User selectable T568A or T568B User selectable crossover settings (Straight through, Half-crossover, Full-crossover) Test speed: 1 second for lengths <393.7' (120 m) |
| Nominal Velocity of Propagation (NVP) | User settable |
| Length (Maximum) | 1000' (305 m) |
| Remote ID Locators | Use remote ID terminations to identify up to 7 unique ports or office outlets |
| Active Network Diagnostics | |
| Diagnostic Protocols | Link Layer Discovery Protocol (LLDP) Cisco Discovery Protocol (CDP) Fast Link Pulses (FLP) Internet Control Messaging Protocol (ICMP) Dynamic Host Configuration Protocol (DHCP) |
| IP | Address setup: LinkIQ address, DNS Server, Gateway for IPv4 or v6 either manually or via DHCP Ping test results: Four response time results for target, DNS Server(s), Gateway, plus average and number lost |
| Nearest Device Diagnostics (If Available Through Diagnostic Protocols) | Switch Name/IP + MAC Address Port Number VLAN Name Advertised Data Rates Advertised Duplex |
| Power Over Ethernet Compatibility | Ethernet Alliance Certified to IEEE 802.3af/at/bt Hardware negotiation with signature resistance Software negotiation with LLDP/CDP |
| Power Over Ethernet Diagnostics | Advertised Power Class (0-8) Advertised Available Power Powered Pairs Diagnostics for both Single and Dual signatures |
| Power Over Ethernet Measurements | Loaded Voltage (V) Loaded Power (W) |
| Port Blink | Blink the light of the connected port |
Click on a category to view a selection of compatible accessories with the Fluke Networks LIQ-100 Cable and Network Tester, 10 GB, 1000'.
| Cable Test | |
| Test Port | Shielded 8-pin modular jack accepts 8-pin modular (RJ45) plugs |
| Commissioning Autotests | 10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, Wire map Only Test Speed: 6 seconds for lengths <229.6' (70 m) |
| Cable Types | Balanced twisted-pair cabling Unshielded twisted-pair Screened twisted-pair 2-pair and/or 4-pair |
| Wire Map-Only Tests | Document wire map Length of each pair Diagnose split pairs User selectable T568A or T568B User selectable crossover settings (Straight through, Half-crossover, Full-crossover) Test speed: 1 second for lengths <393.7' (120 m) |
| Nominal Velocity of Propagation (NVP) | User settable |
| Length (Maximum) | 1000' (305 m) |
| Remote ID Locators | Use remote ID terminations to identify up to 7 unique ports or office outlets |
| Active Network Diagnostics | |
| Diagnostic Protocols | Link Layer Discovery Protocol (LLDP) Cisco Discovery Protocol (CDP) Fast Link Pulses (FLP) Internet Control Messaging Protocol (ICMP) Dynamic Host Configuration Protocol (DHCP) |
| IP | Address setup: LinkIQ address, DNS Server, Gateway for IPv4 or v6 either manually or via DHCP Ping test results: Four response time results for target, DNS Server(s), Gateway, plus average and number lost |
| Nearest Device Diagnostics (If Available Through Diagnostic Protocols) | Switch Name/IP + MAC Address Port Number VLAN Name Advertised Data Rates Advertised Duplex |
| Power Over Ethernet Compatibility | Ethernet Alliance Certified to IEEE 802.3af/at/bt Hardware negotiation with signature resistance Software negotiation with LLDP/CDP |
| Power Over Ethernet Diagnostics | Advertised Power Class (0-8) Advertised Available Power Powered Pairs Diagnostics for both Single and Dual signatures |
| Power Over Ethernet Measurements | Loaded Voltage (V) Loaded Power (W) |
| Port Blink | Blink the light of the connected port |
Click on a category to view a selection of compatible accessories with the Fluke Networks LIQ-100 Cable and Network Tester, 10 GB, 1000'.
