This module analyzes CAN signals for select memory recorders. The module is built to use a baud rate of up to 50kbps to 1Mbps.
This module analyzes CAN signals for select memory recorders. The module is built to use a baud rate of up to 50kbps to 1Mbps.
Connect this Hioki MR8904 Memory HiCorder CAN Signal Module to your Memory HiCorder MR8875 model to analyze CAN signals at a baud rate of up to 50kbps to 1Mbps. The module is equipped with two 9-pin D-sub A male connectors for simple setup.
Features
| Number of Ports | 2 |
| Connectors | 9-pin D-sub A male |
| Standards | ISO 11898 CAN 2.0b, ISO 11898-1, ISO 11898-2, ISO 11898-3, SAE J2411 |
| Interface | High-speed CAN, low-speed CAN, single-wire CAN by port (with built-in corresponding transceiver) selectable |
| Terminator | 120 Ω ±10 Ω built-in resistance, on/off via commands |
| Baud Rate | 50kbps to 1 Mbps (high speed), 10 to 125kbps (low speed), 10 to 83.3kbps (single wire) |
| Analyzed Signal Output Channel | Up to 15 analog channels each equivalent to a 16-bit analog signal; up to 16 logic channels each equivalent to a 1-bit logic signal |
| Signal Form | 1 channel of logic or 1 channel of analog (1-bit signal), 1 channel of analog (1- to16-bit signal), 2 channels of analog (17- to 32-bit signal) *cannot handle signals over 32 bits |
| Response Time | Within 200 μs after completely receiving CAN message |
| Transmit CAN Message | Can transmit the setting CAN message to the CAN bus by a port |
| ID Trigger | Output "H" level pulse to designated logic channel when receiving set ID signal * Output pulse width: 50 μs below 5 ms/div time axis, 1 sampling time at more than 10 ms/div time axis |
| CE Compliant | Yes |
| Product Length | 5.96" (151.5 mm) |
| Product Width | 4.7" (119.5 mm) |
| Product Height | 0.74" (18.8 mm) |
| Product Weight | 6.5 oz (185 g) |
| Manufacturer Warranty | 3 years |
| Number of Ports | 2 |
| Connectors | 9-pin D-sub A male |
| Standards | ISO 11898 CAN 2.0b, ISO 11898-1, ISO 11898-2, ISO 11898-3, SAE J2411 |
| Interface | High-speed CAN, low-speed CAN, single-wire CAN by port (with built-in corresponding transceiver) selectable |
| Terminator | 120 Ω ±10 Ω built-in resistance, on/off via commands |
| Baud Rate | 50kbps to 1 Mbps (high speed), 10 to 125kbps (low speed), 10 to 83.3kbps (single wire) |
| Analyzed Signal Output Channel | Up to 15 analog channels each equivalent to a 16-bit analog signal; up to 16 logic channels each equivalent to a 1-bit logic signal |
| Signal Form | 1 channel of logic or 1 channel of analog (1-bit signal), 1 channel of analog (1- to16-bit signal), 2 channels of analog (17- to 32-bit signal) *cannot handle signals over 32 bits |
| Response Time | Within 200 μs after completely receiving CAN message |
| Transmit CAN Message | Can transmit the setting CAN message to the CAN bus by a port |
| ID Trigger | Output "H" level pulse to designated logic channel when receiving set ID signal * Output pulse width: 50 μs below 5 ms/div time axis, 1 sampling time at more than 10 ms/div time axis |
| CE Compliant | Yes |
| Product Length | 5.96" (151.5 mm) |
| Product Width | 4.7" (119.5 mm) |
| Product Height | 0.74" (18.8 mm) |
| Product Weight | 6.5 oz (185 g) |
| Manufacturer Warranty | 3 years |
