Compact and powerful, this single-phase power controller provides an economical and versatile solid-state option for controlling electric heat. In addition, it is 200KA SCCR with proper fusing to minimize damage in the event of a short circuit and features a 100 to 120 V AC line/load voltage and a phase angle output.
Compact and powerful, this single-phase power controller provides an economical and versatile solid-state option for controlling electric heat. In addition, it is 200KA SCCR with proper fusing to minimize damage in the event of a short circuit and features a 100 to 120 V AC line/load voltage and a phase angle output.
Features
Applications
| Operator Interface | Control input and indication light Alarm output and indication light Current limit indication LED |
| Phase | 1-phase, 1 controlled leg |
| Amperage Rating | Maximum surge current for 16.6 ms, 1350 A peak Maximum I2t for fusing is 9100 A2s Latching current: 500 mA maximum Holding current: 200 mA maximum Off-state leakage 1 mA at 77°F (25°C) maximum Power dissipation: 1.2 W per ampere per leg switched 200KA SCCR, Type 1 and 2 approved with the recommended fusing |
| Line Voltage | 100 to 120 V AC |
| Alarm Output | Energizes on alarm, non-latching Triac 24 to 240 V AC, external supply with a current rating of 300 mA at 77°F (25°C), 200 mA at 122°F (50°C), 100 mA at 176°F (80°C) and a holding current of 200 μA with a latching current of 5 mA typical |
| Terminals | Control input: Compression: Will accept 24 to 16 AWG (0.2 to 1.5 mm2) wire Torque to 4.4 inlb (0.5 Nm) maximum with a ⅛" (3.5 mm) blade screwdriver Line and load: Compression: Will accept 14 to 3 AWG (2.5 to 25 mm2) wire Torque to 24 inlb (2.7 Nm) maximum with a ¼" (6.4 mm) blade screwdriver, or a type 1A, #2 Pozi driver |
| Linearity (Control Options P and L) | ±5% input to output power, as referenced to a sinusoidal power curve, between calibration points |
| Soft Start (Control Options P and L) | Typically: 5 second soft start on power up Soft start on thermostat over temperature Soft start on ½ cycle drop out detection 1 second soft start on set point change |
| Operating Environment | 0 to 90% RH (relative humidity), non-condensing Storage temperature: -40 to 185°F (-40 to 85°C) Operating temperature: -29 to 176°F (-34 to 80°C) Insulation tested to 9842.52' (3000 m) |
| Mounting | DIN-rail: DIN EN 50022, 1.4 x 0.3" (35 x 7.5 mm) Back-panel: Four mounting holes No. 6 to No. 8 (M3 to M4) fastener |
| Agency Approvals | CE with proper filter: 204/108/EC electromagnetic compatibility directive EN 61326-1: industrial immunity Class A emissions not suitable for Class B environments Phase angle and phase angle with current limit are not CE approved for conducted or radiated emissions 2006/95/EC low voltage directive EN 50178 safety requirements installation category III, pollution degree 2 UL® 50 Type 4X enclosure, Class 1, Div. 2 per ANSI/ISA 12.12.01; Through-wall heat sink models T4 File 184390 UL® 508 listed and C-UL® File E73741 2011/65/EU RoHS 2 Shock and vibration tested to IEC 60068-2-32 Vibration tested to IEC 60068-2-6 |
| Dimensions | 7.64 x 5.59" (194 x 142 mm) |
| Operator Interface | Control input and indication light Alarm output and indication light Current limit indication LED |
| Phase | 1-phase, 1 controlled leg |
| Amperage Rating | Maximum surge current for 16.6 ms, 1350 A peak Maximum I2t for fusing is 9100 A2s Latching current: 500 mA maximum Holding current: 200 mA maximum Off-state leakage 1 mA at 77°F (25°C) maximum Power dissipation: 1.2 W per ampere per leg switched 200KA SCCR, Type 1 and 2 approved with the recommended fusing |
| Line Voltage | 100 to 120 V AC |
| Alarm Output | Energizes on alarm, non-latching Triac 24 to 240 V AC, external supply with a current rating of 300 mA at 77°F (25°C), 200 mA at 122°F (50°C), 100 mA at 176°F (80°C) and a holding current of 200 μA with a latching current of 5 mA typical |
| Terminals | Control input: Compression: Will accept 24 to 16 AWG (0.2 to 1.5 mm2) wire Torque to 4.4 inlb (0.5 Nm) maximum with a ⅛" (3.5 mm) blade screwdriver Line and load: Compression: Will accept 14 to 3 AWG (2.5 to 25 mm2) wire Torque to 24 inlb (2.7 Nm) maximum with a ¼" (6.4 mm) blade screwdriver, or a type 1A, #2 Pozi driver |
| Linearity (Control Options P and L) | ±5% input to output power, as referenced to a sinusoidal power curve, between calibration points |
| Soft Start (Control Options P and L) | Typically: 5 second soft start on power up Soft start on thermostat over temperature Soft start on ½ cycle drop out detection 1 second soft start on set point change |
| Operating Environment | 0 to 90% RH (relative humidity), non-condensing Storage temperature: -40 to 185°F (-40 to 85°C) Operating temperature: -29 to 176°F (-34 to 80°C) Insulation tested to 9842.52' (3000 m) |
| Mounting | DIN-rail: DIN EN 50022, 1.4 x 0.3" (35 x 7.5 mm) Back-panel: Four mounting holes No. 6 to No. 8 (M3 to M4) fastener |
| Agency Approvals | CE with proper filter: 204/108/EC electromagnetic compatibility directive EN 61326-1: industrial immunity Class A emissions not suitable for Class B environments Phase angle and phase angle with current limit are not CE approved for conducted or radiated emissions 2006/95/EC low voltage directive EN 50178 safety requirements installation category III, pollution degree 2 UL® 50 Type 4X enclosure, Class 1, Div. 2 per ANSI/ISA 12.12.01; Through-wall heat sink models T4 File 184390 UL® 508 listed and C-UL® File E73741 2011/65/EU RoHS 2 Shock and vibration tested to IEC 60068-2-32 Vibration tested to IEC 60068-2-6 |
| Dimensions | 7.64 x 5.59" (194 x 142 mm) |
