Tramex EIK5.1 Exterior Insulation and Finish Systems Moisture Inspection EIFS Kit includes the Tramex RWS analog non-destructive moisture meter for roof and wall scanning, MRH III (MRH3) digital general building moisture content meter, Hygro-I relative humidity probe and connector cable, HH14TP30 heavy duty pin-type probe, 7” deep wall probes, IRT2 infrared surface thermometer, telescopic handle, HPW hole punch for long pin probes, and heavy duty carry case. The Tramex RWS is designed to scan, survey, and leak trace on building envelopes including on non-conductive single ply membranes, modified and foam roofing systems, and EIFS. The Tramex MRH3 (MRH III) measures moisture content in most building materials such as brick, ceramic tiles, resilient flooring, laminates, roofing, drywall, wood, and plaster.
- Tramex EIK5.1 Exterior Insulation and Finish Systems Moisture EIFS Inspection Kit
- Tramex RWS Moisture Meter Roof and Wall Scanner Kit
- Non-Destructive, deep penetration moisture testing
- 7 inch Pin-Probe for deep penetration
- 7-40 percent readings of moisture content in Wood and 0-100 comparative readings in all other materials
- Clear, easy to read analog/digital dials
- Battery operated (supplied)
- Tramex MRH III Moisture and Humidity Meter
- Reads non-destructively 1 1/4 " deep in wood
- Battery operated (included)
- Automatic default to last user setting when switched back on
- Hold function enables user to "freeze" the reading
- Useful for taking readings when the meter face is not visible
- Switchable "On" or "Off" audio warning tone
- Automatic power cutoff switches "Off" when not in use
- Backlit , large, clear, easy to read LCD display
- Wide range of readings for wood of 5 percent to 30 percent and 0 to 100 comparative for all other materials including drywall, laminate, residential asphalt shingles and masonry products
- External Rubber electrodes make direct contact with the material being tested for best sensitivity and repeatability
- Specific gravity adjustment for most wood species. Deep signal penetration up to over 1 inch into the materials being tested without the need to damage the surface. Signal penetration depends on material being tested and meter setting
- Optional plug in relative humidity probe for relative humidity, temperature, dew point and mixing ratio readings
- Optional plug in wood probe
- Digital, non-destructive moisture meter
- Tramex IRT2 Infrared Surface Non-Contact Thermometer
- -58F° to 1202F° (-50C° to 650C°)
- Switch between C° or F°
- Toggle laser on or off
- Dual laser guidance
- Automatic data hold
- Backlit LCD display
- Indicates when overrange
- Trigger lock
- Displays MAX measurements
- High and low alarms
- Emissivity is adjustable
- Distance to spot ratio 12:1
- Tramex HIPP1 Hygro-I Moisture Probe
- Acclimates quickly
- Reusable - Proves to be the lowest cost per ASTM F2170 test
- Accurate and durable
- Tests per ASTM F2170 and ASTM F2420; Gives in situ relative humidity and ambient RH,
temperature, dew point temperature, and grains per pound - Relative humidity range: 0% to 99%
- Temperature range: -40°F to 176°F (-40°C to 80°C)
- Works with CMEXpert II and MRHIII
- Warranty:
- All Tramex products carry a full satisfaction guarantee including a one year warranty against defects in parts & workmanship and a refund if the unit is returned, shipping pre-paid, in new condition within 21 days of original delivery. Proof of purchase is necessary.
Specifications: | Tramex EIK5.1 Exterior Insulation and Finish Systems Moisture Inspection Kit |
Tramex RWS Moisture Meter Roof and Wall Scanner Kit | |
Size: | 4.9" x 10.8" x 2.9" (125mm x 275mm x 75mm) |
Weight: | 1.88lbs (853g) |
Construction: | ABS Body |
Power: | 9 volt PP3 Battery (included) |
Display: | Analog |
Depth of Penetration: | 4" (100mm) |
Sensitivity: | Four Ranges: Roofing Mode with high and low sensitivity. EIFS / Foam Roof Insulation Mode with high and low sensitivity. |
Accessories: | Leather carry case. Telescopic handle for use on roofs only. |
Limitations: | Some EPDM, Butyl rubber roofing and other conductive roofing. Hard Coat Stucco, wire lath or wire mesh reinforced finishes. |
Tramex MRH III Non Invasive Moisture and Humidity Test Set | |
Size: | 6" x 3.5" x 1.5" (150mm x 85mm x 38mm) |
Weight: | 8.47oz (240g) |
Construction: | ABS Body |
Power: | 9 volt PP3 Battery (included) |
Display: | Digital / Backlit |
Depth of Penetration: | up to1¼"(30mm)(In wood, drywall) |
Measuring Range: | |
Reference scale for building materials: | 0 to 100 |
Relative Humidity (with optional Hygro-i probe) | 0 to 99% |
Wood Non-invasive Mode: | 5 to 55%MC (at SG of 0.3) |
Wood Invasive Mode (with optional wood pin probes): | 7 to 40%MC |
Tramex IRT2 Infrared Surface Non-Contact Thermometer | |
IR Temp Range | -58°F to 1202°F (-50°C to 650°C) |
IR Temp Resoluiton | 1°F (0.5°C) |
Temperature Measurement Accuracy | +/- 4°F/C or +/- 2% of reading >32°F (0°C) +/- 3°F/C or +/- 3% of reading <32°F (0°C) |
Operating Temperature | 32° to 122°F (0°to 50°C) @ 10 to 90%RH |
Emissivity | Adjustable 0.10 ~ 1.0 |
Distance-to-spot Ratio | 12:1 |
Basic Accuracy | ±1.0% of reading |
Response Time | Less than 150ms |
Spectral Response | 8-14µm |
Tramex HIPP1 Hygro-I Moisture Probe | |
Reusable Ambient RH Probe tests: | Temperature, RH %,Dew Point, Mixing Ratio |
Humidity Range: | 0% - 99% RH |
Temperature Range: | 40°F to 176°F (-40°C to 80°C) |
RH Response Time: | 8 sec |
Temperature Response Time: | in. 5 secs. - max. 30 secs. |
Humidity Accuracy: | 0% to 90%RH +/-1.8% @ 25°C / 77°F |
Temperature Accuracy: | +/- 0.5°F / 0.3°C |
NIST Traceable (National Institute of Standards and Technology |
Proposition 65 Warning for California Residents: This product can expose you to chemicals including Benzene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Applications: | Tramex EIK5.1 Exterior Insulation and Finish Systems Moisture Inspection Kit |
Tramex MRH III (MRH 3) Moisture and Humidity Meter | |
Home Inspection | |
Pest Control | |
Indoor Air Quality | |
Water Restoration | |
Industry | Flooring |
Surveying | |
laminates | |
resilient flooring | |
porcelain tiles | |
ceramic | |
brick | |
plaster | |
wood | |
Drywall | |
Material | Residential Roofing |
Asphalt composition shingles | |
Most building materials | |
Tramex RWS Moisture Meter Roof and Wall Scanner Kit | |
Industry | Roofing |
EIFS | |
Tramex IRT2 Infrared Surface Non-Contact Thermometer | |
AC units | |
Ventilation | |
Bearings | |
Motors | |
Transformers | |
Bad Electrical Connections | |
Fuses | |
Hot or cold spots | |
Etc. | |
Tramex HIPP1 Hygro-I Moisture Probe | |
Flooring, Flood Restoration, Indoor Air Quality & Inspection/Surveying | |
Concrete, Masonry, Drywall, Insulation, Air / Environment |
Tramex Hygro-i In-Situ Probes Overview
Related Items
(0)
$2,060.00
Coming Soon
Free Shipping.
(0)
In Stock